Skip to main content

Salsco Roll-N-Go, EHA

“ROLL-N-GO, EHA”
EHA – Elektriske Hydrauliske Aktuatorer

Kjør til greenen, løft hjulene, vals greenen, senk hjulene og kjør videre til neste green.
Selvforsynt system – ingen henger eller nyttekjøretøy nødvendig!

Roll-N-Go, EHA er 30 % mer effektiv enn noen hengerbasert valse.
Med en valsebredde på 91 cm kan den ferdigstille en gjennomsnittlig green på bare seks minutter.

Roll-N-Go, EHA er ikke bare for greener – den fungerer også utmerket på fairways, innspillområder og utslagssteder.

Standard utstyr

Standardfunksjoner inkluderer:
– Skyvbar armlenestol for økt komfort
– Dobbelt drevne oscillerende valser for maksimal trekkraft
– Artikulerende styring for presis manøvrering
– Hydraulisk opererte turfdekk for skånsom kjøring
– Trykk per kvadrattomme (P.S.I.): 10.2 uten vann i valsene og 11.6 med vann i valsene

Options

Flere options å få til rulla, se spesifikasjoner under !

Inner Spike-Air Kit: gjør det mulig å forsiktig prikke greenen, slik at vann og oksygen kan trenge gjennom jordskorpen og nå plantens røtter.

Spesifikasjoner

Modell HP3E
Engine 13HP Honda, electric start, rubber mounted to reduce vibration
Fuel tank 6 gallon, CARB approved canister fuel tank.
Controls On/Off switch, choke & fuel. Raise/ Lower rocker switch for wheels.
Battery 12 Volt, 300 CCA, automotive type
Steering system Both rolls articulate and oscillate to smooth the surface without changing the undulations designed into the green
Steering wheel 13-1/4” diameter, automotive type tilt steering wheel, hydraulic assist steering. 13-1 Ratio
Main Frame 2-1/2” x 2-1/2” x 1/8” steel square tube. Fully gusseted with continuous welds
Drive rolls Two (2) oscillating steel rolls, both driven for positive traction. 1-1/4” roll mounting bearing. 10-3/4” diameter, 36” long with beveled ends. Rolls are machined to within two thousandths of an inch concentricity.
Traction drive Hydraulic pump to two (2) hydrostats – 1 to each roll. Chain drive from hydraulic motors to rolls. #50 chain & sprockets
Climbing traction Up to 40°
Brakes Parking brake
Hydraulic components Hoses: SAE JIC hose ends & fittings. 3,000 P.S.I. working & 12,000 P.S.I. burst.
Motors: Two (2) Char-Lynn 7.3 cubic inch displacement
Pump: One (1) Hydro-Gear, 0.97 cubic inch displacement
Electric hydraulic cylinders Four (4) double action, 6 stroke
Rolling swath 91,4 cm
Speed Variable, 0 – 17,7 km/t
Ground pressure 10.2 P.S.I. without water
11.6 P.S.I. with water
Tire/Wheel assemblies Four (4) 18.5 x 8.5-8, 6 ply, turf tires hydraulically operated. Two are drive wheels
Guards/Decals All moving parts guarded. Full set of safety decals.
Paint Orange, polyester powder coat paint provides excellent outdoor weatherability and offers protection against ultraviolet discoloration. All parts painted separately
Dimensjon rulle L x B x H 1,98 m x 1,68 m x 1,37 m
Transport dimensjoner L x B x H 1,98 m x 1,68 m x 1,45 m
Vekt rulle 671 kg
Standard utstyr Hour Meter
Engine cooling fan
Seat: Molded cushion, arm rest seat with protective edge trim. Neutral safety switch & forward/reverse slide adjustment. Rubber mounted to reduce vibration
Options Top Dressing Brush Kit
Led light kit
Inner Spike-Air Kit
Cross contamination prevention kit
Pedal Extensions
Kontakt oss på mail eller tlf for spørsmål, priser og leveringstid